Imagine you are at the edge of the sea on a day when it is difficult to say where the land ends and the sea begins and where the sea ends and the sky begins. Sea kayaking lets you explore these and your own boundaries and broadens your horizons. Sea kayaking is the new mountaineering.
We took a diversion into a little bay near the north shore of the mouth of Loch Feochan.
At its head stood a delightful cottage with a wisp of smoke rising from its chimney. Access is only by a footpath rising over the hills. There was no sign of a boat. This cottage was used in the 1969 film "Ring of Bright Water" to represent Gavin Maxwell's house Camusfearna (bay of the alders). Other filming took place nearby at the islands of Easdale and Seil. Camusfearna was actually located near the Sandaig Islands much further to the north.
Our first stop was to investigate the ancient fort An dunan, which is the grassy mound at the left of this photo. We landed and launched at the delightful cove of Port an t-Sruthain. I don't know who had most difficulty getting back into their kayak, myself with my bad knee or Jim W with his tiny ocean cockpit.
As the sun began to rise, we made our way into the Firth of Lorn.
We were all looking forward to another fantastic day on the water. None more so than our good friend Jim B.
We then drove 32 km SW to the southern shore of Loch Feochan. The top 3km of the loch was frozen so we had to launch on the sea sea side of the inner narrows. Our plan was to paddle out into the Firth of Lorn then NE by Oban before entering Loch Etive and back to the shuttle car. You do need to get the tides right for this one, as at certain states of the tide, the ebb flows out of Loch Etive over a rock lip known as the Falls of Lora.
From the layby we could see clearer weather to the north and the snow on the distictive peak of Ben Cruachan(1126m) was glinting in the sun. It rises above Taynuilt on the southern shore of Loch Etive.
Back at Lock Feochan, even the seaweed was hiding under a crust of ice.
Phill, Jim B and Jim W joined me in preparing the kayaks.
True gentlemen, they carried my kayak and launched me first as I hobbled down the shore on crutches, trying to avoid ice patches. It's great to have good friends! It is so sad, but this was to be the start of our last adventure with Jim B.
It always amuses me when I see people packing food and drink for their first sea kayaking expedition to Scotland's wonderful west coast. They imagine that such a magnificent, primeval landscape will be as a desert, with little opportunity for resupply or refreshment. But in truth, there chinks in the landscape's armour, little oases, like this one at Kingairloch at the head of Loch a' Choire. This is an apparently insignificant offshoot, into the lands of Morvern, from the 55km length of Loch Linnhe.
David, Phil and I (sadly Jim is no longer with us) have a reputation as light packers yet also as bon vivants, which are apparently contradictory states of sea kayak being. It was shortly after midday when we drew up at the old Victorian Boathouse at Kingairloch Estate in Morvern, which is a wild and remote peninsula deep in Lochaber.
There are no draught beers but the fridge was full of a fine selection of bottled and canned beers and white wines. I enjoyed a bottle or two of some excellent ale from the island of Arran. For our other victuals, Phil chose a local venison burger with fat chips. The venison was almost completely fat free and was aromatic with the heather from the Morven hills upon which the deer had grazed. David enjoyed two starters, a daily special of a terrine of smoked haddock pate with home made bread and a huge cheeseboard, which Phil and I had to help him with. I enjoyed the daily special of a whole plaice cooked in capers with vegetables from the estate garden.
As sea kayakers, we are athletes whose bodies are honed by years of hard expeditioning and as such, they require to be treated like temples. The sad thing is that the "headland to headland" sea kayaking sect (we are a very broad church) would not even notice Loch a' Choire, never mind what lay hidden deep within. Well that is their loss, while they might have battled the midday thermal winds, before dining on an energy bar at the foot of some distant headland, David, Phil and I washed our excellent meal down with some fine filtered coffee. We did however, make a prompt point of being back on the water before three in the afternoon.
The Boathouse is open: Thursday: 11am-8pm*, Friday: 11am-8pm*, Saturday: 11am-8pm*, Sunday Lunch from 12p-3pm. *last orders.
There is free WiFi and the toilets were spotless. Sadly the showers are no longer available, due to lack of demand, so if you visit, ask about showers!
Though not strictly a pub, this is a proper restaurant, we were highly satisfied by our visit. Overall it would seem stingy to give a score of any less than 12/10.
An electric pump will allow you to start paddling and bracing immediately after performing a reentry and roll in rough conditions. I believe it makes a significant contribution to your overall safety in challenging conditions, should the worst happen and you find yourself out of your kayak. There are many different web pages on how to do install a pump but many are complicated, involving many connections switches, relays and connections and some are compromised by the owners reluctance to drill a hole in the kayak. In a marine environment, the more connections you have, the more likely it is that one will fail.
I have chosen a different approach, which uses a minimum number of connections. The Rule 25S-6WC 500GPH automatic bilge pump is designed for jet skis. Inside the pump body an electronic circuit spins up the pump for about a second every 20 seconds. If no resistance (water) is met then it switches off. If resistance is met, it will carry on pumping until air enters the pump inlet when it will stop. After this it will go back to spinning up every 20 seconds. (Some other Rule automatic pumps spin up much less frequently and are therefore unsuitable for kayaks.) The battery draw is negligible. I used it for 10 days in the Outer Hebrides and at the end of the 10 days there was enough battery power to empty the kayak several times. I have chosen not to use a switch or a fuse. I chose to use a sealed lead acid battery because the pump is 12 volts and if you were to use rechargeable AA batteries you would need 10, which is a lot of connections! Also most NIMH AA rechargeable batteries don't hold their charge in storage and it is a hassle to charge 10 just before you go out. They also have poor cold weather performance compared with a sealed lead acid battery.
Rule 25S-6WC pump 12v 1.3Ah sealed lead acid battery fitted with... snap together connector which is soldered to the battery terminals. (I used to use simple spade connectors straight onto the battery terminals but I found they came off.) 12V SLA trickle charger, don't try to use a car battery charger on a small battery like this! Some 3mm sticky backed foam to stick on the back of the battery and the bulkhead, where it will fit against. Velcro hook and loop tape to stick onto the foam pads on the battery and the bulkhead. (I found you get a better "stick" using the foam between the Velcro and hard surfaces.) A 3/4" skin connector for the hose. About 10" of 3/4" hose Unibond "No more nails", waterproof adhesive, which is much more effective than silicone sealant.
The fun starts drilling the hole with a hole saw. I like to put pumps in front of the footrests, next to the forward bulkhead. Put some tape over the gel coat and drill very slowly.
Bed the connector in a little adhesive and screw it up from inside. Glue the pump mounting base (blue) to the hull, because of the vee bottom, I have stuck it slightly off the mid line to get it square on the hull. It is best to roughen the pump base and the hull with coarse abrasive paper then clean both surfaces with a solvent such as alcohol. Leave the pump base glue to dry for 24 hours then fit the hose, heating it in hot water will make it more flexible. Clip the pump into its base. Now drill two 3.2mm diameter holes in the middle of the bulkhead and push the wires through to the front compartment. Seal on both sides with glue. Leave enough wire to bring the pump back to the cockpit opening for cleaning its filter (if it ever gets blocked) and use cable ties to secure the loose wire to the hose.
Working in the front hatch, solder the connectors to the wires. Working outside I find it easier to use one of the little high temperature jet butane lighters than a soldering iron.
Push the plastic connector on to the two terminals and give it a good spray with water dispersant.
Now the whole lot can be assembled together and the battery stuck to a Velcro pad on the bulkhead. You will now hear the pump spin up then stop every 20 seconds until you pull the connector apart. The connector can only clip on one way so you will not be able to reverse the polarity by mistake.
I have tried three different one way valves in the hose. Even the best reduced the flow rate by 50% so I don't bother. You can fit a kitchen sink plug to the outside of the connector. Some people suggest putting a loop in the hose to prevent sea water coming in through the pump but the Rule instructions specifically warn against that as it can create an airlock which will stop the pump.
Does it work?
You bet it does and its simplicity makes it reliable!!
This is why I do not like switches. This switch was mounted in the day hatch with a waterproof boot covering the toggle which went forward through the rear cockpit bulkead. It has seen three seasons' use and was sprayed twice per year with a Suzuki brand wax spray for protecting outboard motor electrics. It did still work when it was removed but for how much longer...?
There are some other links to installing pumps, Here Here Here and Here
A 20km paddle from Brodick on Arran round Holy Island, March 2010.
The north going flood tide enters Lamlash Bay by the South channel and exits by the North Channel the south going ebb tide runs in the reverse direction.
N going flood +0605 HWGreenock -0500 HW Dover, 1knt springs S channel 0.75knt N channel S going ebb +0040 HWGreenock +0200 HW Dover, 1.5 knt springs S channel 1 knt N channel
